The System Folder on “^0” is not valid. This might cause problems during installation, you should make sure the System Folder is valid before continuing.
The System Folder on “^0” is not valid. Installation cannot continue. Make sure the System Folder is valid, then try again.
The selected features could not be installed. Please select Recommended Installation then try again.
An unknown error occurred while running the “^0” program. The installation process has been stopped.
Stopping now may result in an incomplete set of software.
Click Continue to proceed with the installation or click Stop Installation if you are sure you want to stop.
The Installer was not able to quit application “^0”. Installation has been stopped. Quit the application then try the installation again.
The disk “^0” could not be remounted after disk verification was complete. If this is disk requires a password, turn off password protection then try the installation again.
The Drive Setup program cannot be running during this installation.
Please quit Drive Setup then start the installation again.
The selected software components have already been installed/removed.
Click Change Destination to select a different destination disk.
Click Continue to advance to the next panel.
The disk “^0” cannot be checked while other applications are in use.
Click Continue to automatically quit all other open applications.
The action could not be completed. Please try again.
The selection of features could be completed because the connection with the Installer Engine was interrupted. Please try again.
The installation was stopped because the connection with the installer program was interrupted. Please try again.
A selection set file is required to use this program.
The selection set file “^0” is incompatible with this data file. Please create a new selection set file or use a selection set file created for this data file.
The selection set file could not be saved. Please try again.
The selection set file “^0” could not be read because it is damaged.
The partition of the Upgrader application must be at least 1300K for this plug-in to run.
This installation/removal requires a restart and cannot take place while other applications are running.
Click Continue to automatically quit all other running applications. Click Stop to leave your disk untouched.
The Installer was attempting to quit all other open applications, but the process was canceled. Installation has been stopped, leaving your disk untouched.
A removal cannot be preformed because the software component does not exist on the selected destination disk.
This software component may require system software be installed on the selected destination disk before customizing the installation.
Select a disk with system software already installed or install system software then try again.
The helper application “^0” unexpectedly quit. The installation process has been stopped.
Preflight code resource (Type: '^0', ID: ^1, RefCon: ^2) could not be loaded.
Preflight code resource (Type: '^0', ID: ^1, RefCon: ^2) could not be found.
Preflight code resource (Type: '^0', ID: ^1, RefCon: ^2) returned an internal error.
The installation process has been stopped. Stopping now may prevent your computer from starting up.
Click Continue to proceed with the installation.
The installation plug-in could not be loaded.
The hard disk driver on the disk “^0” cannot be updated with this program because the disk is write protected. This disk might have security software installed.
The Apple hard disk driver on the disk “^0” was not updated. Errors were encountered. See the troubleshooting section of your installation manual for more information.
The hard disk driver on the disk “^0” cannot be updated with this program because the disk has been formatted with a non-Apple disk utility. Contact the manufacturer of the disk utility to see if you need to update the driver.
The hard disk driver on the disk “^0” cannot be updated with this program because the disk is not an Apple hard disk. Contact the manufacturer of your computer or hard disk to see if you need to update the driver.
Your computer must have System 7.1.2 or later in order to update the Apple hard disk drivers.
Click Cancel and start up your computer using the disk that came with your upgrade kit, then run this program again.
The selected destination disk is invalid or has unexpectedly disappeared.
Click OK to select another destination disk.
Problems were found on the disk “^0”, but they cannot be fixed because one or more files are open.
Problems were found on the disk “^0”, but they cannot be fixed because the disk is the startup disk. Start up your computer with the CD or startup floppy disk that came with this upgrade kit, then try again.
Problems were found on the disk “^0”, but they cannot be fixed because the disk is locked. Unlock the disk and try again.
Problems were found on the disk “^0”, but they cannot be fixed because file sharing is turned on. Turn off file sharing then try again. (You use the File Sharing control panel to turn off file sharing.)
Problems were found on the disk “^0”, but they have been fixed.
Problems were found on the disk “^0”, but the disk cannot be fixed now. Try starting the installation again.
The disk “^0” is being used by another application. Please quit all other applications and try again.
Problems were found with “^0” that cannot be fixed by this program. See your installation manual for instructions.
Problems were found with “^0” that cannot be fixed by this program. See your installation manual for instructions.
The disk “^0” could not be checked.
An error has stopped the installation process. Some software components have not been installed/removed.
What do you want to do?
• Try to remove ^0 again
• Skip removing ^0
• Stop the entire installation process
The installations or removals that could be completed are finished. However, some could not be completed.
Click Stop to halt the installation process.
The installation process has been stopped. Some software components have not been installed/removed.
What do you want to do?
• Try to remove ^0 again
• Skip removing ^0
• Stop the entire installation process
There are no more software installers to launch.
If you stop the installation process now, some software installers will not be launched.
Are you sure you want to stop?
An error has stopped the installation process. Some software has not been installed.
What do you want to do?
• Try to install ^0 again
• Skip installing ^0
• Stop the entire installation process
All installations that could be completed are finished. Some installations could not be completed.
Click Stop to halt the installation process.
The installation process has been stopped. Some software components have not been installed.
What do you want to do?
• Try to install ^0 again
• Skip installing ^0
• Stop the entire installation process
There is no more software to install.
If you stop the installation now, some software will not be installed.
